Upcoming OSHA Courses

Switch to Calendar View

• VILT | OSHA #501 Trainer Course in Occupational Safety and Health Standards for General Industry

  • Start
    Tue, September 08, 2026
  •  
    8:00 AM
  • End
    Fri, September 11, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    16

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour general industry safety and health Outreach training program to their employees and other interested groups.

  Using the OSHA General Industry Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts. This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour General Industry Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA General Industry Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #511 Occupational Safety and Health Standards for General Industry and have five (5) years of safety and health work experience in general industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA General Industry Outreach Training Program trainers are required to attend OSHA #503 Update for General Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  
  

  Show details
• VILT | OSHA #7505 Introduction to Incident (Accident) Investigation

  • When
    Tue, September 08, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    15

  Register

  
  

  Course Description: This course covers an introduction to basic incident investigation procedures and describes analysis techniques.

  Course topics include reasons for conducting incident investigations, employer responsibilities related to workplace incident investigations, and a four step incident investigation procedure.

  The target audience is the employer, manager, employee or employee representative who is involved in conducting incident and/or near-miss investigations.

  Upon course completion students will have the basic skills necessary to conduct an effective incident investigation at the workplace.

  Minimum student contact hours: 7.5

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #2455 Safety & Health Management Program

  • Start
    Wed, September 09, 2026
  •  
    8:00 AM
  • End
    Fri, September 11, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    13

  Register

  Course Description: 

  Minimum student contact hours: 18

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #7515 Job Hazard Analysis Train

  • When
    Fri, September 11, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    17

  Register

  Course Description: This course covers OSHA guidelines for developing a Job Hazard Analysis.

  Course topics include the purpose and requirements of a job hazard analysis, the relationship between worker tasks and tools in a work environment, identifying job hazards before they occur, and techniques for completing a job hazard analysis.

  Students will participate in activities about utilizing a job hazard analysis.

  Minimum student contact hours: 7.5

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #3115 Fall Protection

  • Start
    Wed, September 16, 2026
  •  
    8:00 AM
  • End
    Fri, September 18, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    7

  Register

  
  

  PETE REGISTRATION 09.16-18.2026

  This course is being offered in partnership with the PETE GRANT.

  Military Members/Veterans/Families must register with the above link. For questions email info@cefotiec.org.

  Course Description: This course covers the OSHA Fall Protection Standard for construction and an overview of fall protection methods.

  Course topics include principles of fall protection, components and limitations of fall arrest systems, and OSHA Standards and policies regarding fall protection. Students will participate in workshops demonstrating the inspection and use of fall protection equipment, residential construction fall protection, training requirements, and developing a fall protection program.

  Upon course completion students will have the ability to assess compliance with the OSHA Fall Protection Standard, evaluate installed passive systems and fall arrest systems, and develop and implement fall protection plans.

  Minimum student contact hours: 18

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #3015 Excavation, Trenching, and Soil Mechanics

  • Start
    Wed, September 23, 2026
  •  
    8:00 AM
  • End
    Fri, September 25, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    14

  Register

  
  

  Course Description: This course focuses on the operations and safety aspects of excavation and trenching.

  Participants are introduced to practical soil mechanics and its relationship to the stability of shored/unshored slopes and walls.

  Various types of shoring (wood timbers and hydraulic) are explained. Testing methods are demonstrated, allowing students to use instruments such as penetrometers, torvane shears, and engineering rods.

  Upon successful completion of this course, students will have the ability to assess employer safety with the current standard, utilize soil-testing methods to classify soil types, determine protective systems for excavation operations, and determine training requirements.

  Minimum student contact hours: 20

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry

  • Start
    Mon, September 28, 2026
  •  
    8:00 AM
  • End
    Thu, October 01, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    13

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour construction safety and health Outreach Training Program to their employees and other interested groups.

  Using OSHA Construction Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts.

  This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour Construction Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized Outreach trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA Construction Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #510 Occupational Safety and Health Standards for Construction and have five (5) years of safety and health work experience in the construction industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA Outreach Training Program trainers are required to attend OSHA #502 Update for Construction Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• IP | OSHA #511 Occupational Safety and Health Standards for General Industry

  • Start
    Tue, September 29, 2026
  •  
    8:00 AM
  • End
    Fri, October 02, 2026
  •  
    4:30 PM
  • Location
    646 Mariposa St. Denver, CO 80204
  • Spaces left
    11

  Register

  Course Description: This course covers OSHA Standards, policies, and procedures in general industry.

  Topics include scope and application of the OSHA General Industry Standards, general industry principles and special emphasis on those areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms found in the OSHA General Industry Standards, identify hazards which occur in general industry, locate and determine appropriate OSHA General Industry Standards, policies, and procedures, and describe the use of OSHA General Industry Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  
  

  
  

  
  

  Show details
• VILT | OSHA #510 Occupational Safety and Health Standards for the Construction Industry

  • Start
    Mon, October 05, 2026
  •  
    8:00 AM
  • End
    Thu, October 08, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    1

  Register

  
  

  PETE/BCC REGISTRATION 10.05-08.2026

  This course is being offered in partnership with the PETE GRANT.

  Military Members/Veterans/Families must register with the above link. For questions email info@cefotiec.org.

  Course Description: This course covers OSHA Standards, policies, and procedures in the construction industry.

  Topics include scope and application of the OSHA Construction Standards, construction safety and health principles, and special emphasis on those areas in construction which are most hazardous.

  Upon course completion students will have the ability to define construction terms found in the OSHA Construction Standards, identify hazards which occur in the construction industry, locate and determine appropriate OSHA Construction Standards, policies, and procedures, and describe the use of the OSHA Construction Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #7500 Introduction to Safety & Health Management

  • When
    Fri, October 09, 2026
  •  
    8:00 AM - 1:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    16

  Register

  Course Description: This course covers the effective implementation of a company’s safety and health management system.

  The course addresses the four core elements of an effective safety and health management system and those central issues that are critical to each element’s proper management.

  This course is an interactive training session focusing on class discussions and workshops.

  Upon course completion students will have the ability to evaluate, develop, and implement an effective safety and health management system for their company.

  Minimum student contact hours: 5.5

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• Free - Trenching & Excavation

  • When
    Fri, October 09, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    646 Mariposa St. Denver, CO 80204
  • Spaces left
    27

  Register

  
  

  
  

  This class will offer an overview of

  • The OSHA trenching & excavation standards
  • Industry best practices
  • Resources for additional trenching & excavation safety assistance

  
  

  This material was produced under grant number 25F50SH000220 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government.

  Show details
• VILT | OSHA #503 Update for General Industry Outreach Trainers

  • Start
    Mon, October 12, 2026
  •  
    8:00 AM
  • End
    Wed, October 14, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    19

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed course #501 Trainer Course in Occupational Safety and Health Standards for General Industry and who are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA General Industry Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain general industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour General Industry Outreach Training Program classes.

  Minimum student contact hours: 18

  Prerequisites: OSHA #501 Trainer Course in OSHA Standards for General Industry. Authorized Outreach Training Program trainers are required to attend this course once every four (4) years to maintain their trainer status.

  Prior to registration, students must provide a copy of their current Outreach trainer card or an official transcript showing successful completion of the OSHA #501 Trainer Course in OSHA Standards for General Industry from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• IP | OSHA #2015 Hazardous Materials

  • Start
    Tue, October 13, 2026
  •  
    8:00 AM
  • End
    Fri, October 16, 2026
  •  
    4:30 PM
  • Location
    646 Mariposa St. Denver, CO 80204
  • Spaces left
    19

  Register

  
  

  Course Description: 

  This course covers OSHA General Industry Standards and other consensus and proprietary standards that relate to the use of hazardous materials.

  Course topics include flammable and combustible liquids, compressed gases, LP-gases, and cryogenic liquids.

  Related processes such as spraying and dipping, and use of electrical equipment in hazardous locations are also discussed. Upon course completion students will have the ability to assess compliance with OSHA hazardous materials standards, determine hazardous (classified) locations, and proper moving, storing, and handling of hazardous materials. 

  Minimum student contact hours: 26

  Prerequisites: None

  
  

  
  

  
  

  Show details
• VILT | OSHA #2264 Permit-Required Confined Space Entry

  • Start
    Wed, October 21, 2026
  •  
    8:00 AM
  • End
    Fri, October 23, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    16

  Register

  
  

  Course Description: This course covers the safety and health hazards associated with permit-required confined space entry in construction and general industry.

  Course topics include recognition of confined space hazards, identification of permit and non-permit required confined spaces, use of instrumentation to evaluate atmospheric hazards, ventilation techniques, development and implementation of a confined space program, proper signage, and training requirements.

  This course features workshops on permit entry classification, instrumentation, and program development.

  Upon course completion students will have the ability to identify permit and non-permit required confined spaces, reference the OSHA Permit-Required Confined Spaces Standards, conduct atmospheric testing, and implement a permit-required confined space program.

  Minimum student contact hours: 20

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #7115 Lockout/Tagout

  • When
    Fri, October 23, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    18

  Register

  Course Description: This course covers the role and responsibilities of employers to develop and implement a hazardous energy control program, or lock-out/tag-out (LOTO), for the protection of workers while performing servicing and maintenance activities on machinery and equipment.

  Course topics include types of hazardous energy, detecting hazardous conditions, implementing control measures as they relate to the control of hazardous energy, developing and implementing energy control programs including written isolation procedures, training of authorized and affected employees, and periodic inspection of energy control procedures using the OSHA Control of Hazardous Energy Standard.

  Upon course completion, the student will have the ability to explain the importance of hazardous energy control programs, procedures, training, audits, and methods of controlling hazardous energy.

  Minimum student contact hours: 7.5

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• IP | OSHA #6005 Collateral Duty Course for Other Federal Agencies

  • Start
    Tue, October 27, 2026
  •  
    8:00 AM
  • End
    Thu, October 29, 2026
  •  
    4:30 PM
  • Location
    CEF Training Center 646 Mariposa St Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers the OSH Act, Executive Order 12196, and the OSHA General Industry Standards.

  This course is intended for federal agency collateral duty safety and health personnel.

  With use of the OSHA General Industry Standards, special emphasis is placed on areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms, identify hazards that occur in general industry, determine appropriate standards and regulations for federal agencies, locate OSHA General Industry Standards, policies, and procedures, and describe the use of the OSHA General Industry Standards and regulations to effectively assist agency safety and health officers with inspection and abatement efforts.

  Minimum student contact hours: 22.5

  Prerequisites: None

  Show details
• VILT | OSHA #511 Occupational Safety and Health Standards for General Industry

  • Start
    Tue, November 03, 2026
  •  
    8:00 AM
  • End
    Fri, November 06, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    13

  Register

  
  

  PETE/BCC REGISTRATION 11.03-06.2026

  This course is being offered in partnership with the PETE GRANT.

  Military Members/Veterans/Families must register with the above link. For questions email info@cefotiec.org.

  Course Description: This course covers OSHA Standards, policies, and procedures in general industry.

  Topics include scope and application of the OSHA General Industry Standards, general industry principles and special emphasis on those areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms found in the OSHA General Industry Standards, identify hazards which occur in general industry, locate and determine appropriate OSHA General Industry Standards, policies, and procedures, and describe the use of OSHA General Industry Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #503 Update for General Industry Outreach Trainers

  • Start
    Wed, November 04, 2026
  •  
    8:00 AM
  • End
    Fri, November 06, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    18

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed course #501 Trainer Course in Occupational Safety and Health Standards for General Industry and who are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA General Industry Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain general industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour General Industry Outreach Training Program classes.

  Minimum student contact hours: 18

  Prerequisites: OSHA #501 Trainer Course in OSHA Standards for General Industry. Authorized Outreach Training Program trainers are required to attend this course once every four (4) years to maintain their trainer status.

  Prior to registration, students must provide a copy of their current Outreach trainer card or an official transcript showing successful completion of the OSHA #501 Trainer Course in OSHA Standards for General Industry from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #502 Update for Construction Industry Outreach Trainers

  • Start
    Mon, November 09, 2026
  •  
    8:00 AM
  • End
    Thu, November 12, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    19

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry and are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA Construction Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain construction industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour Construction Outreach Training Program classes

  Minimum student contact hours: 18

  Prerequisites: OSHA #500 Trainers Course in OSHA Standards for the Construction Industry.

  Authorized Outreach Training Program trainers are required to attend this course once every four years (4) to maintain their trainer status. Prior to registration, students must provide a copy of their current Outreach Training Program trainer card or an official transcript showing successful completion of the OSHA #500 Trainer Course in OSHA Standards for Construction from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #521 OSHA Guide to Industrial Hygiene

  • Start
    Mon, November 09, 2026
  •  
    8:00 AM
  • End
    Thu, November 12, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    18

  Register

  Course Description: This course covers industrial hygiene practices and related OSHA regulations and procedures. Course topics include recognition, evaluation, and control of chemical, physical, biological and ergonomic hazards, Permissible Exposure Limits (PEL), OSHA health standards, respiratory protection, engineering controls, OSHA sampling protocols and strategies, and workplace health program elements. The course features workshops in health hazard recognition, OSHA health standards and use of sampling equipment. Upon course completion students will have the ability to recognize basic industrial hygiene principles and practices, identify characteristics of common air contaminants, locate PELs, perform basic industrial hygiene calculations, and determine methods for hazard control and abatement

  Minimum student contact hours: 26

  Prerequisites: None

  Show details
• VILT | OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry

  • Start
    Tue, November 10, 2026
  •  
    8:00 AM
  • End
    Fri, November 13, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    17

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour construction safety and health Outreach Training Program to their employees and other interested groups.

  Using OSHA Construction Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts.

  This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour Construction Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized Outreach trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA Construction Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #510 Occupational Safety and Health Standards for Construction and have five (5) years of safety and health work experience in the construction industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA Outreach Training Program trainers are required to attend OSHA #502 Update for Construction Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #7505 Introduction to Incident (Accident) Investigation

  • When
    Fri, November 13, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    19

  Register

  
  

  Course Description: This course covers an introduction to basic incident investigation procedures and describes analysis techniques.

  Course topics include reasons for conducting incident investigations, employer responsibilities related to workplace incident investigations, and a four step incident investigation procedure.

  The target audience is the employer, manager, employee or employee representative who is involved in conducting incident and/or near-miss investigations.

  Upon course completion students will have the basic skills necessary to conduct an effective incident investigation at the workplace.

  Minimum student contact hours: 7.5

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• Free - Trenching & Excavation

  • When
    Mon, November 30, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    McClave High School 308 N. Lincoln Ave McClave Co. 81057
  • Spaces left
    15

  Register

  
  

  
  

  This class will offer an overview of

  • The OSHA trenching & excavation standards
  • Industry best practices
  • Resources for additional trenching & excavation safety assistance

  This material was produced under grant number 25F50SH000220 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government.

  Show details
• VILT | OSHA #511 Occupational Safety and Health Standards for General Industry

  • Start
    Tue, December 01, 2026
  •  
    8:00 AM
  • End
    Fri, December 04, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    18

  Register

  Course Description: This course covers OSHA Standards, policies, and procedures in general industry.

  Topics include scope and application of the OSHA General Industry Standards, general industry principles and special emphasis on those areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms found in the OSHA General Industry Standards, identify hazards which occur in general industry, locate and determine appropriate OSHA General Industry Standards, policies, and procedures, and describe the use of OSHA General Industry Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• IP | OSHA #2455 Safety & Health Management Program

  • Start
    Wed, December 02, 2026
  •  
    8:00 AM
  • End
    Fri, December 04, 2026
  •  
    4:30 PM
  • Location
    646 Mariposa St. Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: 

  Minimum student contact hours: 18

  Prerequisites: None

  
  

  
  

  
  

  Show details
• VILT | OSHA #7845 Recordkeeping Rule Seminar

  • When
    Fri, December 04, 2026
  •  
    8:00 AM - 12:00 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    19

  Register

  Course Description: This course covers OSHA requirements for maintaining and posting records of occupational injuries and illnesses, and reporting specific cases to OSHA.

  Upon course completion students will have the ability to identify OSHA requirements for recordkeeping, posting and reporting and to complete OSHA Form 300 Log of Work-Related Injuries and Illnesses, OSHA Form 300A Summary of Work-Related Injuries and Illnesses, and OSHA Form 301 Injury and Illness Incident Report.

  Minimum student contact hours: 4

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• SAFETYFEST MT | OSHA #7845 Recordkeeping Rule Seminar

  • When
    Tue, December 08, 2026
  •  
    8:00 AM - 4:30 PM
  • Location
    MT Safety Fest

  
  

  This class is being offered through Safety Fest MT.

  To attend you MUST register here:

  Safety Fest MT 2026 Registration

  
  

  Course Description: This course covers OSHA requirements for maintaining and posting records of occupational injuries and illnesses, and reporting specific cases to OSHA.

  Upon course completion students will have the ability to identify OSHA requirements for recordkeeping, posting and reporting and to complete OSHA Form 300 Log of Work-Related Injuries and Illnesses, OSHA Form 300A Summary of Work-Related Injuries and Illnesses, and OSHA Form 301 Injury and Illness Incident Report.

  Minimum student contact hours: 4

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #501 Trainer Course in Occupational Safety and Health Standards for General Industry

  • Start
    Tue, December 08, 2026
  •  
    8:00 AM
  • End
    Fri, December 11, 2026
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour general industry safety and health Outreach training program to their employees and other interested groups.

  Using the OSHA General Industry Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts. This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour General Industry Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA General Industry Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #511 Occupational Safety and Health Standards for General Industry and have five (5) years of safety and health work experience in general industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA General Industry Outreach Training Program trainers are required to attend OSHA #503 Update for General Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  
  

  Show details
• VILT | OSHA #3015 Excavation, Trenching, and Soil Mechanics

  • Start
    Tue, December 15, 2026
  •  
    8:00 AM
  • End
    Thu, December 17, 2026
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    16

  Register

  PETE/BCC REGISTRATION 12.15-17.2026

  This course is being offered in partnership with the PETE GRANT.

  Military Members/Veterans/Families must register with the above link. For questions email info@cefotiec.org.

  
  

  Course Description: This course focuses on the operations and safety aspects of excavation and trenching.

  Participants are introduced to practical soil mechanics and its relationship to the stability of shored/unshored slopes and walls.

  Various types of shoring (wood timbers and hydraulic) are explained. Testing methods are demonstrated, allowing students to use instruments such as penetrometers, torvane shears, and engineering rods.

  Upon successful completion of this course, students will have the ability to assess employer safety with the current standard, utilize soil-testing methods to classify soil types, determine protective systems for excavation operations, and determine training requirements.

  Minimum student contact hours: 20

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• IP | OSHA #6005 Collateral Duty Course for Other Federal Agencies

  • Start
    Tue, December 15, 2026
  •  
    8:00 AM
  • End
    Thu, December 17, 2026
  •  
    4:30 PM
  • Location
    CEF Training Center 646 Mariposa St Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers the OSH Act, Executive Order 12196, and the OSHA General Industry Standards.

  This course is intended for federal agency collateral duty safety and health personnel.

  With use of the OSHA General Industry Standards, special emphasis is placed on areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms, identify hazards that occur in general industry, determine appropriate standards and regulations for federal agencies, locate OSHA General Industry Standards, policies, and procedures, and describe the use of the OSHA General Industry Standards and regulations to effectively assist agency safety and health officers with inspection and abatement efforts.

  Minimum student contact hours: 22.5

  Prerequisites: None

  Show details
• VILT | OSHA #510 Occupational Safety and Health Standards for the Construction Industry

  • Start
    Mon, January 04, 2027
  •  
    8:00 AM
  • End
    Thu, January 07, 2027
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA Standards, policies, and procedures in the construction industry.

  Topics include scope and application of the OSHA Construction Standards, construction safety and health principles, and special emphasis on those areas in construction which are most hazardous.

  Upon course completion students will have the ability to define construction terms found in the OSHA Construction Standards, identify hazards which occur in the construction industry, locate and determine appropriate OSHA Construction Standards, policies, and procedures, and describe the use of the OSHA Construction Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• IP | OSHA #5810 Hazards Based Standards for Oil & Gas Exploration and Production

  • Start
    Tue, January 05, 2027
  •  
    8:00 AM
  • End
    Fri, January 08, 2027
  •  
    4:30 PM
  • Location
    CEF Training Center 646 Mariposa St. Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA Construction and General Industry Standards relating to the oil and gas industry.

  This course provides information for employees and employers to protect themselves by developing the knowledge and skills to anticipate, recognize, evaluate and control hazards common to the on-shore oil and gas exploration and production industry. This includes work sites associated with the on-shore exploration and production oil and gas industry including, but not limited to construction, drilling, completion, well servicing, production, product gathering and processing, and product transmission.

  This course is intended for employees and employers engaged in all phases of on-shore oil and gas exploration and production.

  Upon course completion students will be able to determine hazards associated with the oil and gas industry, control and hazard abatement, and use of the OSHA standards, policies, and procedures as they relate to the gas and oil industry. 

  Minimum student contact hours: 30

  Prerequisites: None

  Show details
• VILT | OSHA #503 Update for General Industry Outreach Trainers

  • Start
    Mon, January 11, 2027
  •  
    8:00 AM
  • End
    Wed, January 13, 2027
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed course #501 Trainer Course in Occupational Safety and Health Standards for General Industry and who are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA General Industry Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain general industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour General Industry Outreach Training Program classes.

  Minimum student contact hours: 18

  Prerequisites: OSHA #501 Trainer Course in OSHA Standards for General Industry. Authorized Outreach Training Program trainers are required to attend this course once every four (4) years to maintain their trainer status.

  Prior to registration, students must provide a copy of their current Outreach trainer card or an official transcript showing successful completion of the OSHA #501 Trainer Course in OSHA Standards for General Industry from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• IP | OSHA #511 Occupational Safety and Health Standards for General Industry

  • Start
    Mon, January 18, 2027
  •  
    8:00 AM
  • End
    Thu, January 21, 2027
  •  
    4:30 PM
  • Location
    CEF Training Center 646 Mariposa St. Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA Standards, policies, and procedures in general industry.

  Topics include scope and application of the OSHA General Industry Standards, general industry principles and special emphasis on those areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms found in the OSHA General Industry Standards, identify hazards which occur in general industry, locate and determine appropriate OSHA General Industry Standards, policies, and procedures, and describe the use of OSHA General Industry Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  
  

  Show details
• VILT | OSHA #502 Update for Construction Industry Outreach Trainers

  • Start
    Wed, January 27, 2027
  •  
    8:00 AM
  • End
    Fri, January 29, 2027
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry and are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA Construction Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain construction industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour Construction Outreach Training Program classes

  Minimum student contact hours: 18

  Prerequisites: OSHA #500 Trainers Course in OSHA Standards for the Construction Industry.

  Authorized Outreach Training Program trainers are required to attend this course once every four years (4) to maintain their trainer status. Prior to registration, students must provide a copy of their current Outreach Training Program trainer card or an official transcript showing successful completion of the OSHA #500 Trainer Course in OSHA Standards for Construction from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #3015 Excavation, Trenching, and Soil Mechanics

  • Start
    Mon, February 01, 2027
  •  
    8:00 AM
  • End
    Wed, February 03, 2027
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    19

  Register

  
  

  Course Description: This course focuses on the operations and safety aspects of excavation and trenching.

  Participants are introduced to practical soil mechanics and its relationship to the stability of shored/unshored slopes and walls.

  Various types of shoring (wood timbers and hydraulic) are explained. Testing methods are demonstrated, allowing students to use instruments such as penetrometers, torvane shears, and engineering rods.

  Upon successful completion of this course, students will have the ability to assess employer safety with the current standard, utilize soil-testing methods to classify soil types, determine protective systems for excavation operations, and determine training requirements.

  Minimum student contact hours: 20

  Prerequisites: None

  Show details
• VILT | OSHA #3095 Electrical Standards

  • Start
    Mon, February 01, 2027
  •  
    8:00 AM
  • End
    Thu, February 04, 2027
  •  
    4:30 PM
  • Location
    ZOOM
  • Spaces left
    19

  Register

  
  

  Course Description: This course covers OSHA Electrical Standards and the hazards associated with electrical installations and equipment.

  Course topics include single- and three-phase systems, cord- and plug-connected and fixed equipment, grounding, ground fault circuit interrupters, and safety-related work practices.

  Emphasis is placed on electrical hazard recognition and OSHA Standards, policies, and procedures and applicable portions of the National Electrical Code (NEC). Students will participate in workshops on the safe and correct use of electrical testing equipment.

  Upon course completion students will have the ability to understand the severity of electrical current on the human body, recognize and evaluate actual and potential electrical hazards and reference the applicable OSHA Standard, determine hazard abatement measures, and understand the proper use of electrical testing equipment.

  Minimum student contact hours: 26

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• IP CO | OSHA #7405 Fall Hazard Awareness for the Construction Industry

  • When
    Fri, February 05, 2027
  •  
    8:00 AM - 4:30 PM
  • Location
    646 Mariposa St. Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers the identification, evaluation, prevention and control of fall hazards in the construction industry.

  The course focuses on falls to a lower level rather than falls to the same level resulting from slips and falls.

  Course topics include identifying, analyzing, and preventing fall hazards utilizing OSHA Fall Protection Standards.

  At the conclusion of the course, students will have an awareness level of identifying fall hazards and methods to control and abate the hazards

  Minimum student contact hours: 5

  Prerequisites: None

  Show details
• VILT | OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry

  • Start
    Mon, February 08, 2027
  •  
    8:00 AM
  • End
    Thu, February 11, 2027
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    20

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour construction safety and health Outreach Training Program to their employees and other interested groups.

  Using OSHA Construction Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts.

  This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour Construction Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized Outreach trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA Construction Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #510 Occupational Safety and Health Standards for Construction and have five (5) years of safety and health work experience in the construction industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA Outreach Training Program trainers are required to attend OSHA #502 Update for Construction Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #501 Trainer Course in Occupational Safety and Health Standards for General Industry

  • Start
    Mon, February 22, 2027
  •  
    8:00 AM
  • End
    Thu, February 25, 2027
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    19

  Register

  Course Description: This course is designed for individuals interested in teaching the 10- and 30-hour general industry safety and health Outreach training program to their employees and other interested groups.

  Using the OSHA General Industry Standards as a guide, special emphasis is placed on those topics required in the 10- and 30-hour programs as well as those which are most hazardous.

  Students are briefed on effective instructional approaches and use of visual aids and handouts. This course allows the student to become a trainer in the OSHA Outreach Training Program, to conduct both 10- and 30-hour General Industry Outreach classes, and to issue cards to participants after verifying course completion.

  Students who wish to participate as authorized trainers in the OSHA Outreach Training Program must prepare a presentation on an assigned OSHA General Industry Outreach Training Program topic individually or as part of a group and successfully pass a written exam at the end of the course.

  Minimum student contact hours: 26

  Prerequisites: Students must successfully complete the OSHA #511 Occupational Safety and Health Standards for General Industry and have five (5) years of safety and health work experience in general industry.

  A degree in occupational safety and health, a Certified Safety Professional (CSP) or a Certified Industrial Hygienist (CIH) designation may be substituted for two (2) years of work related experience.

  Students should obtain guidance on whether they meet this requirement from the OSHA Training Institute Education Center where they intend to receive the training.

  Authorized OSHA General Industry Outreach Training Program trainers are required to attend OSHA #503 Update for General Industry Outreach Trainers at least once every four (4) years to maintain their trainer status.

  
  

  
  

  Show details
• IP | OSHA #5810 Hazards Based Standards for Oil & Gas Exploration and Production

  • Start
    Tue, March 02, 2027
  •  
    8:00 AM
  • End
    Fri, March 05, 2027
  •  
    4:30 PM
  • Location
    CEF Training Center 646 Mariposa St. Denver, CO 80204
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA Construction and General Industry Standards relating to the oil and gas industry.

  This course provides information for employees and employers to protect themselves by developing the knowledge and skills to anticipate, recognize, evaluate and control hazards common to the on-shore oil and gas exploration and production industry. This includes work sites associated with the on-shore exploration and production oil and gas industry including, but not limited to construction, drilling, completion, well servicing, production, product gathering and processing, and product transmission.

  This course is intended for employees and employers engaged in all phases of on-shore oil and gas exploration and production.

  Upon course completion students will be able to determine hazards associated with the oil and gas industry, control and hazard abatement, and use of the OSHA standards, policies, and procedures as they relate to the gas and oil industry. 

  Minimum student contact hours: 30

  Prerequisites: None

  Show details
• VILT | OSHA #2055 Cranes in Construction

  • Start
    Mon, March 08, 2027
  •  
    8:00 AM
  • End
    Wed, March 10, 2027
  •  
    4:30 PM
  • Location
    Zoom
  • Spaces left
    20

  Register

  Course Description: This course covers the best practices in crane and derrick operation using the OSHA Cranes and Derricks in Construction Rule as a guide.

  Course topics include hazards associated with crane assembly and disassembly, types of cranes, lifting concepts, rigging and wire rope, signaling, employee qualifications and training, and maintenance, repair, and inspection requirements.

  Students will participate in workshops to reinforce concepts of safe crane operation.

  Upon course completion students will have the ability to identify the types of cranes and their components and attachments, determine safe operating conditions, and recognize common violations of OSHA Standards.

  Minimum student contact hours: 22.5

  Prerequisites: None

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  

  
  

  Show details
• VILT | OSHA #511 Occupational Safety and Health Standards for General Industry

  • Start
    Tue, March 16, 2027
  •  
    8:00 AM
  • End
    Fri, March 19, 2027
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA Standards, policies, and procedures in general industry.

  Topics include scope and application of the OSHA General Industry Standards, general industry principles and special emphasis on those areas in general industry which are most hazardous.

  Upon course completion students will have the ability to define general industry terms found in the OSHA General Industry Standards, identify hazards which occur in general industry, locate and determine appropriate OSHA General Industry Standards, policies, and procedures, and describe the use of OSHA General Industry Standards and regulations to supplement an ongoing safety and health program.

  Minimum student contact hours: 26

  Prerequisites: None

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• VILT | OSHA #503 Update for General Industry Outreach Trainers

  • Start
    Mon, March 22, 2027
  •  
    8:00 AM
  • End
    Wed, March 24, 2027
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed course #501 Trainer Course in Occupational Safety and Health Standards for General Industry and who are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA General Industry Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain general industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour General Industry Outreach Training Program classes.

  Minimum student contact hours: 18

  Prerequisites: OSHA #501 Trainer Course in OSHA Standards for General Industry. Authorized Outreach Training Program trainers are required to attend this course once every four (4) years to maintain their trainer status.

  Prior to registration, students must provide a copy of their current Outreach trainer card or an official transcript showing successful completion of the OSHA #501 Trainer Course in OSHA Standards for General Industry from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details
• OSHA #7105 Evacuation and Emergency Planning

  • When
    Thu, March 25, 2027
  •  
    8:00 AM - 12:00 PM
  • Location
    Zoom
  • Spaces left
    20

  Register

  Course Description: This course covers OSHA requirements for emergency action and fire protection plans.

  Course topics include purpose and requirements of emergency action and fire prevention plans, elements of emergency evacuation plans, and features of design and maintenance of emergency exit routes.

  Students will participate in workshops pertaining to the development of emergency action plans.

  Upon course completion students will have the ability to list the elements of an emergency action plan and emergency evacuation floor plans, recognize violations of OSHA exit route requirements, determine whether their organization requires an emergency action plan, and develop and implement workplace emergency action and fire protection plans.

  Minimum student contact hours: 4

  Prerequisites: None

  Show details
• VILT | OSHA #502 Update for Construction Industry Outreach Trainers

  • Start
    Mon, March 29, 2027
  •  
    8:00 AM
  • End
    Wed, March 31, 2027
  •  
    4:30 PM
  • Location
    VILT - (Zoom)
  • Spaces left
    20

  Register

  Course Description: This course is designed for Outreach Training Program trainers who have completed OSHA #500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry and are authorized trainers in the OSHA Outreach Training Program.

  The course provides an update on OSHA Construction Standards, policies, and regulations.

  Upon course completion students will have the ability to demonstrate continued professional development in their field by applying effective adult learning principles and interactive training techniques to clearly identify, define, and explain construction industry hazards and acceptable corrective measures as they continue to teach the 10- and 30-hour Construction Outreach Training Program classes

  Minimum student contact hours: 18

  Prerequisites: OSHA #500 Trainers Course in OSHA Standards for the Construction Industry.

  Authorized Outreach Training Program trainers are required to attend this course once every four years (4) to maintain their trainer status. Prior to registration, students must provide a copy of their current Outreach Training Program trainer card or an official transcript showing successful completion of the OSHA #500 Trainer Course in OSHA Standards for Construction from their respective OSHA Training Institute Education Center, for verification of trainer status.

  
  

  PLEASE NOTE: 

  This is a Virtual Instructor-Led Training (VILT) for those who reside in the Denver Region (CO, MT, ND, SD, UT, WY). If you reside outside of the Denver Region, you MUST get prior approval from your Region to participate in this course.

  
  

  Show details